Wanco WSP125 99KW Mobile Silent Diesel Generator Variable Voltage Perkins TIER 3

ENGINE

Perkins 1104D-E44TAG2 diesel engine
* Prime -  112kVA / 90kW @1800 RPM
* Standby – 123kVA / 99kW @ 1800 RPM
* 4 Cylinder  4.4 L displacement
* EPA Tier 3 SRE
* Extended warranties available

10 gauge steel double wall fuel tank
* 177 gal. (670 L) capacity
* 24.3 hr. run time - 100% load
* 30.5 hr. run time - 75% load
* 42.1 hr. run time - 50% load
* 70.8 hr. run time - 25% load
* Fuel tank built into skid of generator set
* 120% Containment
* Fork lift Pockets
* Compatible JP5,7,8, NATO F34, 63 and Jet A, A1 with appropriate fuel additive

Oversized Cooling system
Radiator and oil drains plumbed to exterior
Vibration dampers isolate engine/generator from frame
Perkins Factory dual stage air filter
Air cleaner restriction indicator
60 Hz engine/generator - 50 hertz configuration available
Mechanical isochronous governing
Idle switch programmed in DeepSea panel
Standard Block Heater Level 1 Cold Weather package for “Hot Start”

 

GENERATOR

ECP34-2S4C Mecc Alte "Maux PMG"
* Brushless
* 4 pole
* Class H insulation
Automatic Voltage Regulation with upgraded +/- 0.5% DER1 voltage regulator

 

SYSTEM OUTPUTS

3 position voltage selector switch with lock out
* Single phase - 120/240V Zig Zag
* Three phase - 120/208V Low Wye
* Three phase - 277/480V High Wye
* 277/480 Volt, three phase - 129.9 amps standby
* 120/208 Volt, three phase - 299.8 amps standby  
* 120/240 Volt, Single Phase - 254.2 amps standby

 

SYSTEM CONTROLS

Deep Sea controller with heated display
* Backlit LCD display is heated for cold weather application
* -40°F to 185°F (-40°C to 85°C) operating temperature range
* Automatic coarse voltage adjustment
* Integrated fine voltage adjustment
* Remote communication (RS232 & RS485)
* Can and Magnetic pick-up sensing
* Load switching, Load shedding & dummy load outputs
* Customizable status screen and Multiple date & Time scheduler
* Remote display support up to 3 units
* Main utility sensing
* Configurable Event log
* PLC Functionality

Push buttons for easy operation
* Manual or Auto Start
* Engine Start
* Engine Stop/Reset
* Alarm Mute
* Operator Screens
    Home
    Engine
    Generator
    Voltage Adjust
    Configurable display languages

* Scrolling Arrows for Diagnostic information
    Engine diagnostic display
    Oil pressure
    Engine temperature
    Fuel level
    Battery
    After treatment inlet/outlet temperature
    Ash/Soot levels

* Generator diagnostic display
    System kW output display
    Line output & frequency display
    True dual mutual standby with load balancing timer

 

Alarms

    Warning
    Shutdown
    Electrical trip
    Engine

* Alarm List - warnings/shutdowns; 250 event history log - date/time stamp
    Charge Alternator failure alarm
    kW and kVA overload protection
    Unbalanced load protection
    Fuel level: warning - 15%; shutdown - 5%
    Over speed protection: shutdown - 115%
    Oil pressure: warning - 25 psi; shutdown - 20 psi
    Coolant temperature: warning - 220°F (104° C); shutdown - 230° F (110° C)
    Battery voltage: over - 15VDC; under - 11VDC
    Generator over voltage: warning - 110%; electrical trip - 111%
    Generator under voltage: warning - 87%; electrical trip - 86%
    Generator over frequency: warning - 105%; electrical trip - 110%
    Generator under frequency: warning - 95%; electrical trip - 90%
    9 Inputs/ 8 outputs

* Multiple date & time scheduler
* Status
* Configuration of controller, firmware and connections
    DSE configuration Suite PC software
    Remote Monitoring Capabilities
    MODBus, USB, Ethernet connections

 

ELECTRICAL CONTROLS

Lockable control box door with diagnostics window
Lockable lug box and Cam-Lock distribution panels
* Trips main breaker when door is opened

Output ground connection lug inside above cam locks
ABB 125A main breaker with shunt trip
    T5H 400 UL/CSA PR221DS-LSI 400 3P FF

Convenience receptacles with individual breakers operable in high wye
* (2) 120V 20 Amp GFCI duplex outlets - (Nema 5-20R type)
* (2) 125/250V 50 Amp, 3 pole, 4 wire twist lock (Non-Nema 6369)

Voltage adjustment integrated into Deep Sea controller +/- 10%  
Deep cycle rated CCA Group 24 battery
Battery disconnect
Panel lighting for breakers, lugs and selector switch

 

ENCLOSURE

Heavy duty rental grade sound attenuated steel enclosure 12 gauge
* UV & fade resistance, high temperature cured, white polyester powder coat paint
* Insulated closed cell and baffled
* 69 db(A) @ 23 ft. (7 m) - prime power

Fully lockable enclosure including doors and fuel fill
Emergency stop switch located on outside of enclosure
Central lifting point
Operating/safety decals
Document holder with operating manual including AC/DC wiring diagrams

 

TRAILER

DOT approved tail, side, brake, and directional lights - LED
Transportation tie downs
Safety chains with spring loaded safety hooks
2 in. (50.8 mm) ball hitch or 3 in. (76.2mm) pintle hitch
Dual 4000 lb. (1818 kg) axles
2000 lb. (907kg) tongue ag-jack with footplate
ST225/75R12 Load Rating E tubeless
Standard 4 pin trailer connector
License Plate bracket
Electric brakes with brake away kit

 

WEIGHTS & DIMENSIONS

Trailer mounted
* Dry weight: 5790 lbs. (2632 kg)
* Operating weight: 7047 lbs. (3203 kg)
* 186 x 77 x 82 in. (4.725 x 1.95 x 2.08 m)

 

WARRANTY

2 years/2,000 hours
* Engines and alternators used in Wanco mobile generators carry a separate manufacturers (OEM) warranty (the “OEM Warranties”), unless otherwise expressly stated. All warranty claims for defects in material and/or workmanship on Wanco product OEM components should be directed through the OEM distributor/dealer network. OEM Warranties may vary and are subject to change. Wanco shall have no liability under OEM warranties